Julius Bjornsson Posted January 27, 2008 Share #1 Posted January 27, 2008 Advertisement (gone after registration) HI there all. I just got a Summarit 35, and so far the lens appears to be very nice. HOwever there are two things I really do not like about it. The first one is the external thread for the lens hood and the protection ring for that. Now I am sure that I will loose the protection ring. The second is the lens hood which screws onto this external thread. What annoys me is that there does not appear to be any way to fasten the hood. I am not afraid of loosing it, but what happens is that it does not stay in place but rotates. really annoying and if anyone know how to fasten it, that would be great. I would have liked to have the same construction as the 28 Elmarit Asp. Any suggestions appreciated. Link to post Share on other sites More sharing options...
Advertisement Posted January 27, 2008 Posted January 27, 2008 Hi Julius Bjornsson, Take a look here Summarit 35 Lens Hood. I'm sure you'll find what you were looking for!
Julius Bjornsson Posted January 28, 2008 Author Share #2 Posted January 28, 2008 Hey again, is there nobody here who does have a Summarit 35 or 50 and who knows some trick for fastening the hood? Link to post Share on other sites More sharing options...
jflachmann Posted January 28, 2008 Share #3 Posted January 28, 2008 I'm using the Summarit-M 35 with the lens hood but I just don't have your problem. The hood stays on where it should stay. Without any additional fastening! Link to post Share on other sites More sharing options...
marknorton Posted January 28, 2008 Share #4 Posted January 28, 2008 Are they using the same trick as on the WATE with a rubber o-ring around the base of the thread which is compressed as the hood is tightened? Link to post Share on other sites More sharing options...
Julius Bjornsson Posted January 28, 2008 Author Share #5 Posted January 28, 2008 No, there is no rubber ring, just a small notch which stops the hood in the correct position, but the problem is it does not stay there, at least not mine and if I do not take care and check before taking a picture I get some rather annoying shadows. Maybe a very fine rubber ring would solve the problem? I might try that. Link to post Share on other sites More sharing options...
Julius Bjornsson Posted January 28, 2008 Author Share #6 Posted January 28, 2008 Whoops, my last answer was a little premature, there is a rubber ring at the base of the thread. So maybe that needs to be a little thicker. I will look into that. Link to post Share on other sites More sharing options...
Prosaic Posted September 5, 2009 Share #7 Posted September 5, 2009 Advertisement (gone after registration) Same problem here. How did you fix it? Link to post Share on other sites More sharing options...
Julius Bjornsson Posted September 5, 2009 Author Share #8 Posted September 5, 2009 Same problem here. How did you fix it? I went into a shop selling nuts and bolts and such with the rubber ring from the lens and got another one the same size and a little bit thicker and now the hood stays completely in place. And it cost nothing, the guy in the shop gave it to me. You meet nice people sometimes along the way and it is the little things in life that are sometimes great. So the hood is very nice now. Link to post Share on other sites More sharing options...
michael_b_elmer Posted September 5, 2009 Share #9 Posted September 5, 2009 Hej Julius, I had the same lens and exactly the same problems - my solution was to sell the lens. Link to post Share on other sites More sharing options...
stavros_polyviou Posted September 5, 2009 Share #10 Posted September 5, 2009 I had this lens + hood and sold it after buying a used Summilux Asph. My solution to the rotating hood issue was to take a black rubber band (diameter of about 7cm and thickness of about 5mm), slide it over the aperture ring very carefully, install the hood and the carefully move the band so that it covered the base of the hood and the area right in front of the aperture ring about equally. Only problem with this solution was that the hood pretty much lived on the lens from that point on. Hope this helps. Link to post Share on other sites More sharing options...
lars_bergquist Posted September 5, 2009 Share #11 Posted September 5, 2009 Since pretty well time immemorial, quality cameras like Rolleiflex and Hasselblad have used bayonet-mount hoods (and in these two cases, also bayonet filters). Zeiss ZM lenses all have bayonet-mount hoods. Even the lenses that Cosina sell under the Voigtländer name are beginniong to appear with front bayonets, and hoods to fit. If Cosina can fit bayonets into their clearly very tightly controlled production budgets, why then must Leica, of all people, opt for such a barely functional, 'cheapie' solution as screw-in hoods with a clearly tacky positioning system for the rectangular hoods? Admittedly, the snap-on hoods, with a fastening system that goes back to the 1950's, was a clumsy solution, especially on short lenses. But replacing it with what we are now seeing, is a very bad idea indeed. It is just barely acceptable for cylindrical hoods, that can simply be screwed tight without any orientation problems. But for 18mm, 21mm, 24mm, 35mm, even 50mm --- no, no, NO! Fix bayonets! And if you must, Charge! The old man from the Age of Push-On Hoods Link to post Share on other sites More sharing options...
kiteland Posted September 5, 2009 Share #12 Posted September 5, 2009 Hi had (have) the same lens and problem. Solution was to wrap the thread with a small amount of plumbers PTFE tape. The hood now fits very snugly. This was to be a short term solution until I bought another “rubber ring” but I’ve ended up leaving like that as it works and you cant see the tape when the hood is on. Peter Link to post Share on other sites More sharing options...
akiralx Posted September 5, 2009 Share #13 Posted September 5, 2009 Hej Julius, I had the same lens and exactly the same problems - my solution was to sell the lens. Me too, after the hood unscrewed and fell off onto a stone floor with a huge metallic clang... Very bad design flaw. Link to post Share on other sites More sharing options...
a.noctilux Posted January 11, 2024 Share #14 Posted January 11, 2024 I found simple solution with screw-in vented hood (not Leica though). I happend to use this kind of hood in many Leitz/Leica lenses, so I have many 39mm/43mm/46mm/etc. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now