rrf Posted July 8, 2015 Share #1 Posted July 8, 2015 Advertisement (gone after registration) Hi folks,I have a problem with my Leicaflex SL and I'd really appreciate some advice. When I bought it, I put in a Cris adapter with a 386 battery - the meter worked just fine for about 2 weeks, and then just stopped working. Since then, I've tried several fresh 386 batteries with the Cris adapter and no joy with the meter. A google search found some mentions of the Cris adapter not working well with the SL. I really like the option of having a meter in camera, so I'd be very grateful for a solution, based on your experience.Many thanks,Raj Quote Link to post Share on other sites More sharing options...
Advertisement Posted July 8, 2015 Posted July 8, 2015 Hi rrf, Take a look here Advice on batteries for Leicaflex SL. I'm sure you'll find what you were looking for!
wildlightphoto Posted July 8, 2015 Share #2 Posted July 8, 2015 I re-calibrated the meter to use a 1.5-volt 625s silver-oxide battery. Quote Link to post Share on other sites More sharing options...
dkCambridgeshire Posted July 8, 2015 Share #3 Posted July 8, 2015 Not every type of PX 625 battery used to work in the SL battery chamber - it's fussy. I recall that Kodak brand PX 625 batteries worked but other well known brands did not - even though they looked identical. You might try adding some silver foil to the battery adapter to slightly enlarge it. dunk Quote Link to post Share on other sites More sharing options...
AB007 Posted July 9, 2015 Share #4 Posted July 9, 2015 (edited) I have been using wein cell batteries on my Leicaflexes without any adapters or modifications. I have been using it on my SL, SL2, SL MOT and SL2 MOT. I have never use the adapter you are talking about. Not sure where you are located. Wein cell batteries can be easily bought easily in the US. Edited July 9, 2015 by AB007 Quote Link to post Share on other sites More sharing options...
rrf Posted July 9, 2015 Author Share #5 Posted July 9, 2015 Thanks, everyone, for your advice. I'll try the solutions you proposed. Quote Link to post Share on other sites More sharing options...
Hugh 38 Posted October 6, 2015 Share #6 Posted October 6, 2015 Following on from the above , I have just had to dump an original 1.35V battery as it was exhausted. I was wondering about putting in a modern 1.5V battery . I can easily adjust the film speed to compensate . However might I damage the electronic parts inside by putting in the 1.5V battery ? Any advice ? Otherwise I may get the SL2 camera adjusted . Quote Link to post Share on other sites More sharing options...
masjah Posted October 7, 2015 Share #7 Posted October 7, 2015 Advertisement (gone after registration) Would you forgive my stating the obvious checks? If your adapter worked for about two weeks, then it seems unlikely that the problem is the physical fit of the adapter in the camera. There are two further possibilities that ought to be checked out. Firstly, has the adapter coincidentally failed? (A voltmeter across it might be worth a try.) Secondly, has the camera's metering coincidentally failed? Quote Link to post Share on other sites More sharing options...
Rodin Clark Posted October 12, 2015 Share #8 Posted October 12, 2015 (edited) Personally I think this is much ado about very little. I experimented with using Canon F1's with alkaline batteries, shooting transparencies, and had no difficulty whatever getting good exposures. I began by installing a fresh battery of each type and could see only a tiny difference in the meter's needle position, very much less effect than the change of one-half stop of exposure. As you know the more serious problem with the alkaline batteries is that the voltage sags when not new. What that means is that after you install a new 1.5 alkaline the voltage will begin to approach 1.35, so that for most of the battery's life the voltage will more or less approximate 1.35. I was careful to replace the battery once or twice a year depending on usage, and as I said, never a problem. That having been said, I did stock up on some mercury Vartas on a trip to Ireland after availability in the USA became problematic and happily there were still some in the icebox after my recent purchase of a couple of Leicaflex SL's, so I have not repeated the experiment with the the alkalines. Edited October 12, 2015 by Rodin Clark Quote Link to post Share on other sites More sharing options...
sc_rufctr Posted October 14, 2015 Share #9 Posted October 14, 2015 I like the MR-9 Mercury Battery Adapter by C.R.I.S. It just works. There are other options on Ebay. Quote Link to post Share on other sites More sharing options...
philcycles Posted October 15, 2015 Share #10 Posted October 15, 2015 I use the Wein air cells. Some batteries are too thick for the SL battery chamber and the cover stands proud of the plate. Quote Link to post Share on other sites More sharing options...
miha Posted October 15, 2015 Share #11 Posted October 15, 2015 I'm using one of his adapters: http://www.butkus.org/chinon/batt-adapt-us.pdf Works perfectly fine in my SL. Quote Link to post Share on other sites More sharing options...
Dr Davidson Posted November 12, 2018 Share #12 Posted November 12, 2018 The best option is an adapter to take 675 zinc-air cells, they last long enough and are cheap as they are supplied for hearing aids. Look in ebay for an adapter, there are some good ones from Japan. Quote Link to post Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.